Press the check button on the battery cartridge to indi-cate the remaining battery capacity. Important safety instructions for battery cartridge. Applicable battery cartridge and charger: WARNING: Only use the battery cartridges and chargers listed above. After operation, remove dust from both sides of the blades with a wired brush, wipe it off with a cloth and then apply low-viscosity oil (machine oil, or spray-type lubricating oil) to the blades. Do not touch the terminal of the tool imme-diately after use as it may get hot enough to cause burns. Noise:The typical A-weighted noise level determined accord-ing to EN50636-2-94: DUM111 with shear blade for grass shear installed Sound pressure level (LpA) : 70 dB(A)Uncertainty (K) : 1.5 dB(A)The noise level under working may exceed 80 dB (A).The typical A-weighted noise level determined according to EN62841-4-2: DUM111 with shear blade for hedge trimmer installedSound pressure level (LpA) : 70 dB(A)Uncertainty (K) : 3 dB(A)The noise level under working may exceed 80 dB (A). Home Makita makita DUM111 Cordless Grass Shear Instruction Manual. Release the hinge of the grass receiver from the tool. The chip receiver gathers discarded leaves and makes clean-up afterward much easier. To remove the chip receiver, press the levers on both sides to release the hooks. Do not nail, cut, crush, throw, drop the battery cartridge, or hit against a hard object to the battery cartridge. The actual shearing height may vary depending on the condition of the lawn or the ground.NOTE: Try a test shearing in a less conspicuous place to get your desired height. Adjust the three pins so that they are lined up on the alignment line. The tool is equipped with a tool/battery protection system. It may result in a risk of overheating, possible burns, and even an explosion. To install the blade cover, perform the steps in reverse. The lightest and heaviest combinations, according to EPTA-Procedure 01/2014, are shown in the table. The shearing height can be set to three levels (15 mm, 20 mm, and 25 mm) by changing the fixed position of the grass receiver. Installing or removing the chip receiverOptional accessory. View cart for details. NOTICE: Never try to remove the chip receiver by an excessive force with its hooks locked in the holes of the blades. Store the tool out of the reach of children. Shear blade assembly (for grass shear use), Long handle attachment (for grass shear use), Shear blade assembly (for hedge trimmer use), Shear blade cover (for hedge trimmer use). Never recharge a fully charged battery cartridge. Then turn the tool on to restart. WARNING: Wear ear protection.WARNING: The noise emission during actual use of the power tool can differ from the declared value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.WARNING: Be sure to identify safety measures to protect the operator that is based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). When trimming to make a round shape (trimming box-wood or rhododendron, etc. Overheat protectionWhen the battery is overheated, the tool stops automatically. Pay attention to the handling of hot battery cartridges. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. CAUTION: Never use the tool without installing the undercover. Due to our continuing program of research and development, the specifications herein are subject to change without notice. Clean the tool by wiping off dust with a dry cloth or one dipped in soapy water and wrung out. Ask your local Makita Service Center for repairs.WARNING: Never disable the lock function or tape down the lock-off button. Make sure that the lock lever fits in the groove on the undercover. NOTE: Sliding the blade cover forward slightly makes it easier to install the shear blades. Adjusting the shearing height (for grass shear)Optional accessory. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.CAUTION: Do not install the battery cartridge forcibly. While pressing the lock lever, turn the undercover counterclockwise until on the undercover is aligned with on the lock lever. Hold the tool with one hand, pull the switch trigger while pressing the lock-off button, and then move it forward. Release the switch trigger to stop. Cutting long lawnDo not try to cut long grass all at once. Gently move the tool forward. Do not simultaneously wear multiple belt harnessesand/or shoulder harnesses when operating the tool. Keep children and bystanders away while operating a power tool. Place the undercover so that the under-cover is aligned with the lock lever. Always stop tool operation and charge the battery cartridge when you notice less tool power. Attach the crank to the pins with its small and large rounds facing down. WARNING: The vibration emission during actual use of the power tool can differ from the declared value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). The indicator lamp also lights up when the tool becomes overloaded. 33 product ratings - Makita DUM111ZX 18v 110mm LXT Grass Shears Bare Unit Hedge Trimmer 2-in-1 Garden. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. It may result in loss of your eyesight. NOTICE: Do not use the tool in a way that causes the motor to stop or to rotate extremely slowly.NOTICE: Do not attempt to cut thick branches.NOTICE: Do not allow the shear blades to con-tact the ground during operation. Never use the tool if it starts when you pull the switch trigger without pressing the lock-off button. In this case, let the tool and battery cool before turning the tool on again. NOTE: The shearing height value is a guideline. The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. Prepare the crank, undercover, and new shear blades. The blades will be dulled, causing poor performance.NOTICE: Do not trim the wet grass or foliage of small trees. SAVE THESE INSTRUCTIONS.CAUTION: Only use genuine Makita batteries. Installing or removing battery cartridge:CAUTION: Always switch off the tool before installing or removing of the battery cartridge.CAUTION: Hold the tool and the battery cartridge firmly when installing or removing the battery cartridge. To prevent the switch trigger from being accidentally pulled, a lock-off button is provided. The tool may recoil and cause an injury.CAUTION: Overreaching with a hedge trimmer, particularly from a ladder, is extremely dangerous. Indicating the remaining battery capacity:Only for battery cartridges with the indicator. Portable power pack PDC01. Charge the battery cartridge before completely discharging. The blades may break and cause an injury.CAUTION: Be careful not to allow the shear blades to contact the ground. For European countries onlyThe EC declaration of conformity is included as Annex A to this instruction manual. There seems to be a problem serving the request at this time, One stop shop for all things from your favorite brand, {"modules":["unloadOptimization","bandwidthDetection"],"unloadOptimization":{"browsers":{"Firefox":true,"Chrome":true}},"bandwidthDetection":{"url":"https://ir.ebaystatic.com/cr/v/c1/thirtysevens.jpg","maxViews":4,"imgSize":37,"expiry":300000,"timeout":250}}. Some of the battery cartridges and chargers listed above may not be available depending on your region of residence. Comment document.getElementById("comment").setAttribute("id","a2a818a4ed96fd61077050bbdd4bfa95");document.getElementById("afe6277d1c").setAttribute("id","comment"); Save my name, email, and website in this browser for the next time I comment. Shearing (for grass shear):Turn the tool on after adjusting the shearing height and hold it so that the bottom of the tool rests on the ground. Turn the shear blades upside down and install them so that the pin on the tool fits in the hole on the shear blades. Release the protrusions on the grass receiver from the grooves on the tool while sliding the grass receiver toward the front of the tool. NOTICE: When replacing the shear blades, do not wipe off grease from the gear and crank. They may differ from country to country. WARNING: Before shearing, clear away sticks and stones from the shearing area. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Need Help? Tips for maintaining maximum battery life. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking the function on the tool. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. Insert the claw of the guide plate into the groove on the tool. Remove the blades and install them again. Do not work while standing on anything wobbly or infirm. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. Align the protrusions on the grass receiver with the grooves on the tool by sliding the grass receiver toward the front of the tool and moving it in the direction of the arrow. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. General power tool safety warnings:WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. During and after use, the battery cartridge may take on heat which can cause burns or low temperature burns. Doing so may cause rust or damage to the tool.NOTICE: Dirt and corrosion cause excessive blade friction and shorten the operating time per battery charge. Power tools create sparks that may ignite dust or fumes. Attach the crank to the pins with the small and large rounds facing up. While pressing the undercover, turn the under-cover clockwise until on the undercover is aligned with on the lock lever. Leave a day or two between cuts until the lawn becomes evenly short. NOTICE: Do not cut down dead trees or similar hard objects. For the preparation of the item being shipped, consulting an expert for hazardous material is required. It may result in poor performance or breakdown of the tool or battery cartridge. Let a hot battery cartridge cools down before charging it. Change the fixed position of the grass receiver by moving it in the direction of the arrow. Use of this site is subject to certain Terms Of Use. Adjust the blades and guide plate so that the hole in the guide plate and the two protrusions on the blades are lined up. It is an employers responsibility to enforce the use of appropriate safety protective equip-ments by the tool operators and by other persons in the immediate working area. The use of any other accessories or attachments might present a risk of injury to persons. It will also void the Makita warranty for the Makita tool and charger. cordless hedge trimmer (108 pages), Cordless grass shear / cordless hedge trimmer (96 pages), Cordless grass shear / The tool will automatically stop during operation if the tool or battery is placed under one of the following conditions: Overload protectionWhen the battery is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops. Loosen two screws with a screwdriver and remove the shear blades. NOTICE: Do not attach the hinge of the grass receiver to the tool forcibly after aligning the protrusions on the grass receiver with the grooves on the tool. It can be installed on either side of the tool. Place the undercover so that on the under-cover is aligned with on the lock lever. Tighten the two screws firmly with a screwdriver. To remove the blade cover, pull it slightly, and then slide it side-ways. Use of any other battery cartridges and chargers may cause injury and/or fire. The indicator lamps light up for a few seconds. Charge the battery cartridge with room temperature at 10 C 40 C (50 F 104 F). The time at which the indicator lamp lights up varies depending on the temperature around the work area and the battery cartridge conditions. Apply a small amount of grease to the periphery of the crank. Distractions can cause you to lose control. Slide the shear blades so that the hole on the guide plate is positioned at the center of the rings of blades. NOTICE: If the shear blades do not operate prop-erly, the blades are not engaging the crank prop-erly. Storage:The hook hole in the tool bottom is convenient for hanging the tool from a nail or screw on the wall. For basic operation, tilt the blades toward the trimming direction and move it calmly and slowly at the speed rate of 3 to 4 seconds per meter. Hook the hinge of the grass receiver on the groove of the tool. Apply a small amount of grease to the periphery of the crank. Remove the blades and install them again. Only use accessory or attachment for its stated purpose. The cord-connected power source(s) listed above may not be available depending on your region of residence. Remove the blade cover, and then turn on the tool to check that it works properly. by third parties, forwarding agents, special requirements on packaging and labeling must be observed. Slide the grass receiver toward the front of the tool. Trim large branches to the desired height using branch cutters before using this tool. ), trim from the root to the top for a beautiful finish. If the cartridge does not slide in easily, it is not being inserted correctly.
Fox 38 Pressure Release Button, Mitchell And Ness Nba T-shirt, Yellow Diamond Earrings Men's, Crimp Terminal Size Chart, Clear Reflective Paint, Reclaimed Wood Hutch And Buffet, The Bell At Sapperton Dog Friendly, Karcher Pressure Washer Fitting, Infant Crew Neck Wholesale, Bead Landing Mini Pliers,
